Collection: 60 Inch Bathroom Vanities

What 60 Inches Actually Gives Two People

60 inch bathroom vanities are the default double-sink width, and the arithmetic explains why. Split down the middle, a 60 inch vanity gives each person about 30 inches of their own, which is roughly the width of a small single vanity each. That is enough for a bowl, a faucet and a strip of counter beside it, but it is not enough for either of you to spread out.

This is the width where doubles start. Sizing guides put double vanities as beginning at 60 inches and commonly running to 72. Everything below 60 is a single with two bowls forced into it; everything at 60 and above is a purpose-built double. Across the wider category of double sink bathroom vanities the 60 inch width is the one that shows up most.

The Standard Size of a Double Vanity

The standard size of a double vanity is 60 to 72 inches wide, with 60 the entry point and 72 the size most people move to when the wall allows. Depth and height do not change with width. Standard cabinet depth stays at about 21 to 22 inches, and cabinet height before the countertop commonly falls between 32 and 36 inches, with taller households sometimes specified at roughly 40.

Width is the only figure that varies much, which is worth knowing when you compare listings. A 60 inch double and an 84 inch double are the same cabinet logic with different amounts of middle. If you want more room between the bowls rather than more bowls, look at what changes at 72 inch bathroom vanities before you decide.

A Single Sink at 60 Inches Is a Legitimate Choice

A single sink in a 60 inch vanity is not a compromise, and for a lot of bathrooms it is the better call. One bowl means one drain, one set of supplies and one faucet, and every inch you do not spend on the second sink becomes counter or drawer space. You end up with a long, uninterrupted run of surface that a split top can never give you.

It suits three situations in particular. A bathroom used by one person who wants storage rather than a second basin. A shared bathroom where the two people are never at the sink at the same time. And a renovation where the existing plumbing is in one place and moving it would mean opening the floor.

Single-sink 60s are usually offset, with the bowl to the left or right and a full run of counter on the other side, or centred with drawers on both flanks. If that layout is closer to what you want, the wider selection of single bathroom vanities is worth comparing against the doubles.

One Mirror or Two Over a 60 Inch Vanity

Over a 60 inch vanity, two mirrors suit two sinks and one mirror suits one. The mirrors should line up with what is below them: a mirror centred over each bowl reads as deliberate, while two mirrors floating over a single centred sink reads as a mistake. If your vanity has one bowl, run one mirror and let it do the work.

With two bowls, each mirror should be narrower than the sink cabinet section it sits over, so there is visible wall between and either side of the pair. That gap is also where a pair of sconces goes, which is the lighting layout most designers prefer over a single bar above one wide mirror. With one bowl, a single wide mirror or a mirrored cabinet can run most of the counter width, stopping short of both ends.

Whichever you choose, measure the wall against the countertop rather than the cabinet, because the top overhangs by roughly half an inch to an inch per side.

Storage Under a 60 Inch Double Vanity

Two sinks mean two drain assemblies and two sets of supply lines, and both of them run down through the cabinet. That is the storage reality of any double, and it shapes the layouts you will see.

• Doors under each bowl, drawers in the middle — the most common double layout. The plumbing stays behind doors and the middle drawers stay full depth.
• Drawers across the front — the top drawer is notched around the traps, so it is shallower than it looks. Lower drawers are usually full depth.
• Single sink, full drawer bank — the layout with the most genuinely usable volume, because only one side has plumbing in it.

If drawers matter more than a second sink, that last row is the honest answer. A 60 inch single-sink vanity holds noticeably more than a 60 inch double, and nothing about the footprint changes.

Measuring the Wall Before You Order a 60 Inch Vanity

Sixty inches of cabinet needs more than sixty inches of wall. Add the countertop overhang on both ends, then check what sits at each end of the run — a door casing, a shower jamb or a towel bar all eat into the space you thought you had. Trade practice is also to keep at least 18 inches between the vanity and the centerline of the toilet, and on a 60 that clearance is what usually decides whether the vanity lands where you drew it.

Check the floor in front too. If accessibility is part of the plan, the ADA 2010 Standards use 30 inches wide by 48 inches deep of clear floor for a forward approach, a lavatory rim no higher than 34 inches above the finished floor, and 27 inches of knee clearance at the front edge. In a private home those are design benchmarks rather than legal requirements, but a 60 inch vanity is wide enough to build an open knee space at one end and keep full storage at the other. If the wall will not take 60, compare the single-sink options at 48 inch bathroom vanities rather than shrinking a double past the point where it works.